O-Ring Powersteering
Thread Starter
|
Member
Joined: Aug 2008
Posts: 37
From:
O-Ring Powersteering
Hello,
i am on Holiday with my H3 in Hungary and noticed that my Powersteering is leaking a bit. It's not the highpressure-line, it's the connection between the pump and the reservoir.
I figured out that there is a oring ( # 10388957) to seal the connection.
No Opel-dealer in hungary has this partnumber in his computer...
Can somebody give me the measurement of this oring?
I don't want to rip everything apart to get the measurement, because it is only leaking a little bit, yet.
With the measurement of the oring i can get a new one before i cause a bigger leak.
Thank you in advance.
jens
i am on Holiday with my H3 in Hungary and noticed that my Powersteering is leaking a bit. It's not the highpressure-line, it's the connection between the pump and the reservoir.
I figured out that there is a oring ( # 10388957) to seal the connection.
No Opel-dealer in hungary has this partnumber in his computer...
Can somebody give me the measurement of this oring?
I don't want to rip everything apart to get the measurement, because it is only leaking a little bit, yet.
With the measurement of the oring i can get a new one before i cause a bigger leak.
Thank you in advance.
jens
Senior Member
Joined: Jul 2012
Posts: 8,999
From: C-Town
Thread Starter
|
Member
Joined: Aug 2008
Posts: 37
From:
Thank you for the tip with the oring set. I have such a set at home and noticed several times that the thickness of the orings would be to less in many cases...
Am i right with my guess that the inner diameter of the oring should be around 12mm (1/2")?
Then i would get 12mm (1/2") orings with several outer diameters and would put in the one that fits best.
jens
Am i right with my guess that the inner diameter of the oring should be around 12mm (1/2")?
Then i would get 12mm (1/2") orings with several outer diameters and would put in the one that fits best.
jens
Thread Starter
|
Member
Joined: Aug 2008
Posts: 37
From:
Hey,
according to a picture on rockauto, where both o-rings (pressure-side and reservoir) are displayed, the o-ring for the reservoir should be around 16mm id and 23mm od.
I try to get home with my slight leaking reservoir and try out a few o-ring sizes next week. I will and post here, wich one fits best.
greetings,
jens
according to a picture on rockauto, where both o-rings (pressure-side and reservoir) are displayed, the o-ring for the reservoir should be around 16mm id and 23mm od.
I try to get home with my slight leaking reservoir and try out a few o-ring sizes next week. I will and post here, wich one fits best.
greetings,
jens
Thread Starter
|
Member
Joined: Aug 2008
Posts: 37
From:
Hello,
back in germany and o-ring changed.
The best fitting o-ring on the reservoir is a 16mm ID and 22mm OD.
The o-ring for the pressure line has an ID of 8mm and an OD of 12mm.
I used NBR O-rings from a local hydraulic supplier.
back in germany and o-ring changed.
The best fitting o-ring on the reservoir is a 16mm ID and 22mm OD.
The o-ring for the pressure line has an ID of 8mm and an OD of 12mm.
I used NBR O-rings from a local hydraulic supplier.
Thread
Thread Starter
Forum
Replies
Last Post
mismatch
PRIVATE For Sale / Trade Classifieds
10
Mar 27, 2012 05:23 AM
ctdrl-1
PRIVATE For Sale / Trade Classifieds
2
May 10, 2010 11:42 AM