Has anyone installed a oil gauge in thier rig?
#1
Has anyone installed a oil gauge in thier rig?
Was wonderung if anyone installed a oil guage in thier h3? If so, was it electric or mechanical? How did you run it? Would appreciate hearing about it...thanks dave
#7
Good morning from germany.
I'm on my way to install an oil pressure gauge on my 2006 H3, because i had the idiot light on when the truck was in idle. It was only a plugged oil pickup screen, but you all know how bad it is, to get the oil pan dropped....
Now i want to see my oil pressure all time, to be able to react before the oil light comes on.
There is a good tutorial on "355nation" i used to find the location and the fittings to get the pressure pickup installed.
https://www.355nation.net/forum/i4-i...ure-gauge.html
The thread above the oil filter, where the plug is removed, is metric M16 x 1,5.
As far as i know, does the pcm not provide data of the motor oil pressure...
Have a nice day...
Jens
I'm on my way to install an oil pressure gauge on my 2006 H3, because i had the idiot light on when the truck was in idle. It was only a plugged oil pickup screen, but you all know how bad it is, to get the oil pan dropped....
Now i want to see my oil pressure all time, to be able to react before the oil light comes on.
There is a good tutorial on "355nation" i used to find the location and the fittings to get the pressure pickup installed.
https://www.355nation.net/forum/i4-i...ure-gauge.html
The thread above the oil filter, where the plug is removed, is metric M16 x 1,5.
As far as i know, does the pcm not provide data of the motor oil pressure...
Have a nice day...
Jens
Last edited by jens; 04-10-2018 at 01:38 AM. Reason: Wrong thread size!!! It's M16 x 1,5!!!
#9
Hey,
i finished installing an oil pressure gauge on my H3.
I had to clean the oil pickup screen, because it was clogged with pieces of carbon and i had the oil pressure alarm.
I used the discription, i wrote of in my previous post...
Here is a picture of the oil pressure sensor in place...
I placed the gauge on the left corner of the dashboard...
I even checked and cleaned up my valvecover...
You can see the missing sealant on the baffles. The H3 smoked a little bit blue, 20 seconds after startup
i removed the baffles and cleaned everything up?..
... and sealed everything with new rtv...
Tomorrow i have to reassamble the whole thing and check everything up...
i finished installing an oil pressure gauge on my H3.
I had to clean the oil pickup screen, because it was clogged with pieces of carbon and i had the oil pressure alarm.
I used the discription, i wrote of in my previous post...
Here is a picture of the oil pressure sensor in place...
I placed the gauge on the left corner of the dashboard...
I even checked and cleaned up my valvecover...
You can see the missing sealant on the baffles. The H3 smoked a little bit blue, 20 seconds after startup
i removed the baffles and cleaned everything up?..
... and sealed everything with new rtv...
Tomorrow i have to reassamble the whole thing and check everything up...
Last edited by jens; 04-25-2018 at 02:47 PM.
Thread
Thread Starter
Forum
Replies
Last Post
kramcard6
PRIVATE For Sale / Trade Classifieds
34
02-25-2013 02:56 PM
8lug
PRIVATE For Sale / Trade Classifieds
10
01-27-2013 12:59 PM
Intercooled
PRIVATE For Sale / Trade Classifieds
3
06-26-2008 12:07 PM
Coug_H2
PRIVATE For Sale / Trade Classifieds
1
04-15-2007 07:09 PM
whth3
PRIVATE For Sale / Trade Classifieds
2
01-11-2007 08:53 AM