Tail Lights
Login  | |
|
Tail Lights - 4/21/2007 5:25:43 PM
|
|
|
Dennis
Posts: 7584
Score: 0
Status: offline
|
As our HUMMERS age some of the bulbs are starting to burn out and need replacing..
My right rear Turn Signal lamp burned out..So while I was in there I changed out all the bulbs in both Taillight assemblies..(4 bulbs in all)
Replacement bulb for all the four bulbs in both Taillights (2 ea) are;
3157 LL (LL= long life) $5.00 for a pack of two.
If y'all don't mind, I will attempt to explain as to how to remove the Taillight Assy...(I know someone explained this before..But, you try to find it )
1. Remove the two small Phillips head screws holding the inside edge of the Taillight assy (you have to open the tailgate)
2. Pull straight back on the Taillight assy levering most of your pressure to the outside edge.
(There is two peg like things [top and bottom of the assy] stuck into a tight fitting hole in the body, so it will take some effort, as they are pretty snug..but, they should eventually pop out)
(Put a dab of vasoline on the pegs before you stick them back in, this makes future entries easier)
3. Twist each lamp base 1/4 turn CCW and the lamp base/holder will come right out of the Taillight assy.
4. While grasping the bulb, Pull straight out from the base..Insert new Bulb.
(Spray a little lubricating contact cleaner in the socket and on the bulb base, before you put the new bulb in.)
5. Add a little vinly/rubber spray protectant to the rubber gasket on the base.
6. Re-install Lamp and base into Taillight assy using a 1/4 turn CW twist of your wrist
7. Align the pegs on the Back of the Taillight assembly with the mating holes on the body.
8. Gently, but firmly smack the Taillight assy with the heel of your hand, to seat the pegs.
9. Re-install and tighten the two screws and go wipe off the finger prints and smudges from Taillight assy lens.
10. Repeat for the other side. (left side, after you remove the screws, close the tailgate)
< Message edited by Dennis -- 4/21/2007 11:10:43 PM >
|
|
|
|
|
|
|
RE: Tail Lights - 4/21/2007 6:56:36 PM
|
|
|
Racerboy80
Posts: 126
Score: 0
Joined: 1/1/2007
Status: offline
|
quote:
(Put a dab of vasoline on the pegs before you stick them back in, this makes future entries easier)
My wife keeps telling me the same thing...
_____________________________
2007 Birch White HUMMER "Like Nothing Else" H3
"Sometimes There's Justice...Sometimes There's Just Us"
|
|
|
|
|
|
|
RE: Tail Lights - 4/21/2007 8:49:35 PM
|
|
|
blackstangs281
Posts: 6758
Score: 0
Joined: 11/13/2005
From: Pittsburgh PA
Status: online
|
You forgot bulb grease
_____________________________
|
|
|
|
|
|
|
RE: Tail Lights - 4/21/2007 9:05:22 PM
|
|
|
blackstangs281
Posts: 6758
Score: 0
Joined: 11/13/2005
From: Pittsburgh PA
Status: online
|
Very good detailed instructions.
_____________________________
|
|
|
|
|
RE: Tail Lights - 4/22/2007 3:50:01 AM
|
|
|
HummBob
Posts: 15593
Score: 0
Joined: 5/6/2006
Status: offline
|
quote:
ORIGINAL: Racerboy80
quote:
(Put a dab of vasoline on the pegs before you stick them back in, this makes future entries easier)
My wife keeps telling me the same thing...
FUNNAY!!!!!
_____________________________
2004 Black Hummer H2
2007 Black Escalade
 
|
|
|
|
|
RE: Tail Lights - 7/17/2007 3:47:56 PM
|
|
|
f5fstop
Posts: 50
Score: 0
Joined: 7/13/2005
Status: offline
|
I would never use Vaseline jelly on any plastic parts on a vehicle that will be in temps that exceed 98 degrees F. Vaseline is designed to melt at or around 98-99 degrees and is mixture that contains high amounts of unique waxes and paraffin. Melting jelly is not good, and it leaves behind wax residue, may cause some plastic to seize to plastic. (I say may, not will, depends on the situation.)
If you want to lube these locating and/or fastening pins, use a lithium grease or a dry lube (such as made by Kent Industries). Personally, I would never lube these parts.
|
|
|
|
|
RE: Tail Lights - 7/17/2007 5:24:56 PM
|
|
|
Dennis
Posts: 7584
Score: 0
Status: offline
|
quote:
ORIGINAL: f5fstop
I would never use Vaseline jelly on any plastic parts on a vehicle that will be in temps that exceed 98 degrees F. Vaseline is designed to melt at or around 98-99 degrees and is mixture that contains high amounts of unique waxes and paraffin. Melting jelly is not good, and it leaves behind wax residue, may cause some plastic to seize to plastic. (I say may, not will, depends on the situation.)
If you want to lube these locating and/or fastening pins, use a lithium grease or a dry lube (such as made by Kent Industries). Personally, I would never lube these parts.
I'm glad you used this disclaimer, the same can be said for WD-40 in that, it dissolves some plastics..BUT NOT ALL....In this case, the vaseline will only help with an easy removal again in the future of the lamp assembly and won't hurt a thing..There is a thread here where someone changed out their lights and broke the plastic inserts that the pegs engages, while he was trying to remove the lamp assemblies..they were stuck on good....I must confess, mine broke too and I repaired them with epoxy..So a little dab of any grease will work..but most people have vaseline...Let us know when you have to change your Brake light bulbs..I'd like to hear how it went.
|
|
|
|
Contact Us |
Advertising |
Automotive Directory |
About Us |
Link To Us |
Archive |
Hummer Links |
Legal |
Privacy Policy |
© Hummer Forums.com
Hummer Forums .com is not affiliated with or endorsed by General Motors Corporation.
|
Printable Version
