i work for hummer

ok mods you can move this where ever you like but i figured ide join the site to help anyone out who needs help. i work for a hummer dealer and can excess most info when needed. also if anyone would like to do a group buy feel free to PM me and i can get prices!!

What do you do for the dealer( parts, service, sales )? Always welcome people who can help.

Howdy RYKID!!!!

Talk about timely!  Thanks for offering to help and welcome to the forum.

I have a challenge as outlined below.  Wonder if you or anyone at your dealer might know of a solution.  Thanks in advance.

I have a 2006 H2.  Also have Travel Trailer that I want to pull.  Trailer is within weight limits of H2.  The H2 has stock rear spare tire carrier.

The problem is the spare tire clearance does not allow weight distribution hitch to mount without a long extension.  Long extension is not a good idea.

I was wondering if anyone has solved problem and if so, how did you do it? Move tire, special hitch adaptor, etc..

How about wiring diagrams for a 2007 H3. I need IPC, Radio, PCM, and BCM diagrams.
 
Sam

quote:

ORIGINAL: SamHouseIII

How about wiring diagrams for a 2007 H3. I need IPC, Radio, PCM, and BCM diagrams.

Sam

Hey Bro,just checked Alldata......no H3 ....hmmmmmm.. hope you find info by the time you want to install all the new toys

AS FOR THE TOING QUESTION....THEY MAKE A CARRIER THAT GOES INSIDE INSTEAD OF MOUNTED ON THE BACK?? I KNOW THATS NOT THE ANSWER YOUR LOOKING FOR BUT.... AS FOR ME IM IN THE PARTS DEPT. AND I WENT ONTO OUR SERVICE INFO WEBSITE AND I CANT FIND A DIAGRAM ON THE WIREING. ANYTHING YOUR TRYING TO DO AND MAYBE I CAN NAROW IT DOWN?

Rykid   Can you help me find the info I need to mount the GPS navigation antenna under the dash.  I am installing a 2006 H2 touchscreen nav unit in my 2003 H2.  I have the unit installed but need to know where to mount the GPS ant. under the right side of the dash. Does anyone know if the GPS ant needs to be mounted at a certain angle or posistion or can I just pick any good place to mount it. There is about 2 feet of wire coming off the nav unit so I know it goes somewhere by the pass air bag but any help or pictures you could help with would be appreciated.

IM PRETTY SURE IT MOUNTS DIRECTLY BEHIND THE RADIO. THERE SHOULD BE 2 SCREWS ALREADY THERE? ILL ASK A TECH AND FIND OUT FOR YOU ASAP

quote:

ORIGINAL: Lampooner

I have a 2006 H2.  Also have Travel Trailer that I want to pull.  Trailer is within weight limits of H2.  The H2 has stock rear spare tire carrier.

The problem is the spare tire clearance does not allow weight distribution hitch to mount without a long extension.  Long extension is not a good idea.

 
i pull a 26' camper, with a slightly extended weight distro hitch.  the only problem i had was with the hitch jack on the trailer - came with a manual crank which didn't work with the spare in the way.  changed to electric, but i mounted it so the controls are to the side instead of in front.  that gives me enough clearance with the spare mounted.  a long as i don't get the trailer off at an ugly angle it works fine. 

 
Thanks to all who responded to hitch question.
 
At the risk of answering my own question, the solution seems to be as follows:

Buy the Equal-i-zer weight distributing hitch, which is available without a shank, the piece that goes into the receiver on H2.  Also order the shank which gives a 9" drop and a 12" extension.  This will clear under the tire and with the hitch itself extending beyond the shank arm, it will clear the tire itself.

Found this out from a person on RV.net.  He tows the same trailer I have with an H2, very helpful fellow.
 
I have also ordered an electric jack for front of trailer.
 
Thanks again.

Have you looked at the Alumistinger ball mounts. I have one and really like it. Looks good and doesn't weigh much.

Alumistinger ball mounts
Calif phil, those look nice, can they handle the weight? I may have to pick one up myself!  Thanks!
 

rykid, welcome aboard here is some information I would like to ask for on a 2007.5 H3:
 
P/N and type/model Alternator.
P/N and size of the throttle body.
P/N and size of the MAS/MAF Sensor.
Bolt Pattern # of bolts for the front axle pumpkin i.e. 9" or 8.5.
Bolt Pattern # of bolts for the rear axle pumpkin.
Battery P/N and size L-W-H i.e. 34T, 35T, D75/25?
Spark Plug type/P/N
Cam Shaft (s) Specs int and exh lift
Torque specs for the Valve Cover.
Fuel Injector type (Mutec, Delphi, Seimans etc...) and Size.
 
Here are some questions for the H3 Alpha Crowd.
 
P/N and Type/Model Alternator.
H3 Alpha Air Filter Size= L-W-H " and P/N for those who have an Alpha.
5.3 V8 type is it a LS series Gen III or IV or LS1?
Cam Specs and stock Rocker arm ratio i.e. 1.6, 1.7, 1.8 ?
Throttle Body size and P/N.
Coils, Coil on Plug P/N and type i.e Delco style unit for the Delphi System.
Intake Mainfold P/N and is it a LS1 or LS6 type.
 
That's it for now Thanks.
 
 

to get you the correct part numbers i need a vin number

Well I am here in Iraq, can I suggest you take it off of one in the lot? i know the H3 3.7 would be an 08 but i haven't read that there are any specific changes from the two model years. Same suggestion for the Alpha, if you can't do that I guess I will have to wait or if anyone on here is willing to provide it, it would be up to them.
 
Thanks 

BMJM100  Yes the alumistinger I have is good for 10,000 Lbs I think.  I was skeptical at first but it is very well made and it sure looks strong. Made In USA too. 

i just PMed someone for the alpha he sent me his vin. im sure he will post all the info

I sent my vin# to rykid and here's what he sent me back:
 
OK SO FAR HERE IS WHAT I FOUND FOR YOU  i can fax you all kinds of things with pics if you need it
 
this fits your h3 and these parts are by your vin.

intake manifold   12580420
alt 145 amp 15905872
air filter (dont stock one yet so i can measure) 15942429
engine says 8cyl 5.3l sfi ho
throtle body 12580760
plugs 12571164 the short ac delco number is 41-985
coils they have 2 designs
1st design *square shaped coil 12570616
2nd design is a round shaped..12573190

THOSE PARTS ARE FOR THE ALPHA!!!!

Hey Rykid,
Welcome to the site! I also have a question, as you have probably seen my recent posts. I have an 08 Alpha built in August 2007. I would like to know if there is a TSB# for the lowering intermeddiate steering shaft or any parts around there, that involve a clunk in the gas/brake pedal. The Hummer Customer Care line said there was, but he couldn't give me the number because it was against the rules....and well my service advisor could care less to find out...TIA!!!!

I NEED VIN NUMBERS. PM THEM TO ME

Hey Ryan
 
Received the SMA Door Buckets today!!!
 
They're PERFECT!!!
 
Thanks Brother!!!

I got the wiring diagrams here. Best I have seen!!
 
http://www.ahdol.com/
 
Sam